Professional provision of Chemical Auxiliaries
Provide high-quality products and technical services
Phone:0086-19876879286
Whatsapp:+86 13712258351
Enquiry
{name}{name} DEL
Contact Us
  • Dongguan Ruikun Material Technology Co.,Ltd.
  • TEL:0086-19876879286
  • Mobile phone:0086-19876879286
  • Whatsapp:+86 13712258351
  • Email:info@bestrkchem.com
  • Add:Jianshe Road, Nancheng District, Dongguan City

Which wetting agent manufacturer in Huizhou is reliable? Where do"craters"(pinholes) come from, and how can you improve substrate wetting?

2026-11-21

Which wetting agent manufacturer in Huizhou is reliable? Where do "craters" (pinholes) come from, and how can you improve substrate wetting?

 

For factories in Huizhou that handle coatings for 3C (consumer electronics) products and home appliances, one of the most dreaded defects is the appearance of "craters"—small, pit-like depressions that emerge on the paint film, as if a drop of oil had landed on the surface. Often, the first assumption is that the paint itself is contaminated; operators might spend days checking filtration systems or cleaning processes, yet the problem persists. In reality, the root cause of these craters usually lies at the interface: the liquid paint has failed to spread completely and uniformly across the substrate.

 

I. "Fish eyes" (craters/pinholes) are generally not a problem with the paint itself; rather, they are typically an interfacial issue.

For a liquid coating to spread effectively over a substrate, its surface tension must be lower than the substrate's surface energy. The greater this difference, the better the spread. If the substrate is contaminated—by oil, mold-release agents, or fingerprints—the local surface energy drops. The paint then retracts from those specific points, creating "fish eyes." This is a matter of physics, not a flaw in the formulation.

 

Therefore, when addressing fish eyes, first determine whether the cause is substrate contamination or the paint’s own surface tension being too high. The former requires cleaning and surface pretreatment, while the latter requires the addition of wetting agents. Attempting to tackle both simultaneously often leads to failure on both fronts. Identifying the cause is straightforward: spray the same batch of paint onto two panels—one cleaned and one uncleaned. If the fish eyes appear only on the uncleaned panel, the issue lies with the substrate.

 

Another phenomenon that is easily confused with this is the "crater" (or volcano-like defect). While a standard fish eye involves the paint retracting to expose the substrate, a "crater" typically features a particle or foreign object at its center, with the paint pulled away from it. In the former case, you should investigate contamination; in the latter, you should examine filtration and dispersion. Identifying the specific shape reveals the correct course of action.

There is also a phenomenon known as the "picture frame" effect. During spraying, the paint may retract from the edges toward the center, leaving a thin, frame-like border. This is largely related to surface tension gradients and the drying rate. While wetting agents can provide some mitigation, adjustments to spraying parameters are also necessary.

 

II. Substrate Wetting vs. Coating Wetting: Two Distinct Concepts

The term "wetting agent" is often used as a broad, catch-all concept, but it actually encompasses two separate processes. The first involves the wetting of pigments by the liquid coating—a matter of dispersion—while the second concerns the wetting of the substrate by the coating—a matter of interfacial spreading. This article focuses on the latter.

Substrate wetting must be evaluated dynamically. When atomized droplets from a spray application land on a substrate, there is only a very brief window of time for them to spread; as the solvent evaporates and the viscosity rises, this window closes. Additives that exhibit low static surface tension may not necessarily be able to migrate to the newly formed interface within such a short timeframe. This explains why some wetting agents perform well in a beaker but prove ineffective when used on an actual production line.

 

III. Polyether-Modified Silicones: The Agents for Lowering Surface Tension

Polyether-modified silicones are the primary agents used for substrate wetting. Their siloxane segments provide low surface tension, while the polyether segments ensure compatibility with the overall system; varying the ratio between these two components results in different performance characteristics. Products such as RK-8026 and RK-8065 are frequently employed for substrate wetting in both waterborne and solvent-borne systems applied to plastic or metal components (these are provided as examples to illustrate specific molecular structure types).

It is important to be mindful of their tendency to migrate. It is the inherent nature of siloxanes to migrate toward interfaces; however, excessive migration can lead to defects such as craters (fish-eyes) or surface mottling (blooming). Overdosing can result in the formation of "craters" or an "orange peel" texture on the film surface—creating more problems than it solves. To determine whether the dosage is appropriate, one should observe the spreading behavior of the coating after it has been atomized and applied to the substrate, rather than relying solely on surface tension readings taken in a beaker.

 

IV. The Non-Silicone Alternative: Ideal for Overcoating and Overprinting

Non-silicone wetting agents contain no siloxanes; instead, they utilize acetylenic diol or fluorocarbon structures to reduce surface tension. Acetylenic diols offer excellent dynamic wetting and low foaming tendencies, while fluorocarbons are highly efficient—though they come at a higher cost and face stricter environmental requirements. Products such as RK-8030 or RK-8014 (cited here as examples of specific molecular structures) are more reliable choices for applications that require subsequent overcoating or overprinting.

In manufacturing processes—such as those common in Huizhou—that involve multi-layer coating (e.g., applying a UV topcoat over a primer, or printing characters onto a colored base coat), the migration of silicone additives poses a genuine risk. Opting for non-silicone agents in these scenarios may slightly reduce the spreading rate, but it effectively eliminates potential complications in later stages of production.

While fluorocarbon wetting agents are highly efficient, they are expensive, subject to stringent environmental regulations, and notoriously difficult to remove once they have migrated. Consequently, they are generally reserved for specialized substrates or surfaces that are particularly difficult to wet, rather than being used as a standard, go-to option.

A key advantage of non-silicone acetylenic diol-based agents is their low foaming tendency. In waterborne systems, foam is already difficult to manage; a wetting agent that introduces additional foam only compounds the problem during the spreading process. This issue is particularly pronounced when working with high-gloss clear coats.

 

VI. Dosage, Addition Sequence, and Risks of Overdosage

There is an optimal dosage range for wetting agents. Too little, and the coating will not spread properly; too much, and it may lead to defects such as craters or surface mottling (uneven appearance). It is advisable to conduct a gradient test, starting from the lower end of the dosage range, to observe the spreading behavior of the atomized droplets upon contact with the substrate, and subsequently evaluate the film surface after drying.

Regarding the sequence of addition, wetting agents should ideally be introduced during the final stages of paint formulation, spaced out from the addition of defoamers. Since both agents compete at the interface—with defoamers working to break bubbles and wetting agents striving to stabilize the interface—adding them too close together can cause them to counteract each other. This principle has been consistently validated in practical, real-world applications.

Another critical detail concerns the mixing process. If the mixture is stirred too rapidly while adding a wetting agent, a vortex may form on the surface, drawing air into the liquid—which, ironically, necessitates the addition of even more defoamer. In a production environment, it is worth repeatedly emphasizing three key practices: using a low stirring speed, proceeding slowly, and adding the agent along the side of the mixing vessel.

 

VII. Validation and Selection

The most accurate way to validate substrate wetting is to test it on the actual substrates. Apply the product to three types of samples—uncleaned boards from the production line, cleaned boards, and reworked parts with oil contamination—then observe the spreading behavior and check for any cratering (pinholes). Follow this with cross-hatch (grid) and adhesion testing to ensure that the wetting agent does not compromise intercoat (interlayer) strength.

Dongguan Ruikun Material Technology Co., Ltd. is a specialized manufacturer of polymer additives. With an in-house R&D department and dedicated production facilities, the company synthesizes its products via chemical reactors rather than simply blending or rebranding existing formulations. Its comprehensive product portfolio includes defoamers, dispersants, leveling agents, wetting agents, anti-oil additives, and anti-scratch agents. These products offer stable chemical structures and reliable performance, meeting the requirements of various application systems. With localized supply, competitive pricing, and short lead times, the company helps clients effectively manage their procurement costs.

Wetting agents, defoamers, and leveling agents interact in a complex, three-way dynamic at the interface. Partnering with a single supplier capable of balancing all these components can significantly reduce the costs associated with formulation tuning and optimization.

 

Frequently Asked Questions

 

Q: Are "craters" (fish-eyes) always caused by the paint itself? A: Not necessarily. Contaminants on the substrate—such as oil, mold-release agents, or fingerprints—can lower the local surface energy, causing the liquid paint to retract and form craters. To identify the source, compare a cleaned panel with an uncleaned one.

 

Q: Can a single wetting agent address both pigment wetting and substrate wetting? A: These are two distinct processes. Pigment wetting relates to dispersion, while substrate wetting concerns interfacial spreading. Before selecting an additive, clarify which specific issue you need to resolve.

 

Q: Why might a wetting agent perform well in a beaker but fail during an actual production run? A: In spray application, the window for spreading is very short; a low static surface tension does not guarantee a fast dynamic response. Performance must be evaluated based on how the paint actually spreads after atomization and contact with the substrate.

 

Q: What happens if too much polyether-modified silicone is added? A: It can lead to craters, orange peel, or pigment flooding/floating; it may also interfere with recoatability. It is better to use less rather than more—start with a low dosage and conduct a gradient test.

 

Q: Why are non-silicone wetting agents preferred for multi-coat systems? A: Siloxanes can migrate and create an interfacial barrier, which may negatively affect the adhesion of subsequent layers (such as clear coats or overprints). While non-silicone agents may spread more slowly, they pose a lower risk to recoatability.

 

Q: Is there a risk of chemical reaction when using wetting agents in two-component (2K) polyurethane systems? A: Yes—additives containing active hydrogen can react with isocyanates, potentially affecting the pot life and surface-drying time. Always verify the functional groups when selecting an additive.

 

Q: Can wetting agents and defoamers be used together? A: They can, but they should be added at different stages. Since both compete for space at the interface, adding them too close together can diminish their respective effectiveness.