Are oil-resistant additive manufacturers in Huizhou reliable? How can one achieve both good spreading and strong adhesion on oil-contaminated substrates?
In the 3C and home appliance coating industry in Huizhou, "oil" is an unavoidable challenge. Plastic parts arrive coated in mold-release agents, metal components carry cutting fluids, and items requiring rework often bear fingerprints from previous processing stages. While cleaning is a standard step, it is not always perfectly executed—leading some to consider oil-resistant additives as a safety net for inadequate cleaning. This approach is only half-right.
I. Two Types of Oil: Mold Release Agents and Process Oils
The oil found on plastic parts is typically an injection-molding release agent—either silicone-based or wax-based—forming a thin, invisible layer that feels slightly slippery to the touch. Oil on metal parts, by contrast, consists of cutting fluids or rust preventatives; these have more complex compositions, ranging from mineral oils to synthetic esters. These two types of oil affect the coating process differently: the former causes the paint to retract (pull away from edges), while the latter often leads to poor adhesion.
Anti-oil additives (oil-repellent or wetting agents) are highly effective against the first type, as they alter the interfacial tension, allowing the paint to spread even on surfaces with low surface energy. However, they are largely ineffective against the second type; since the oil film remains present—acting as a barrier between the paint film and the substrate—adhesion issues are inevitable. If you cannot distinguish between these two types of oil, any amount of anti-oil additive used will be a waste.
II. It Alters Surface Tension, Not Cleanliness
This point must be made clear: anti-oil agents (oil-repellent/surface-tension-modifying additives) do not possess cleaning properties. Their function is to lower the surface tension of the paint to a sufficient degree, allowing it to spread evenly even over surfaces contaminated with oil. The oil remains present; it is simply "covered up." Consequently, while these agents can effectively prevent "fish-eyes" (crawling/shrinkage), they cannot ensure proper adhesion.
Some users mistakenly treat these agents as a substitute for cleaning—applying them and then painting directly without prior cleaning. While the finish may appear acceptable in the short term, issues will inevitably surface during rigorous testing, such as a cross-hatch adhesion test or a salt-spray test. In our view, anti-oil agents should be reserved for scenarios where cleaning has already been performed but minor residues persist; they should not be used as a shortcut to bypass necessary cleaning steps.
Another relevant scenario involves rework. Reworking typically requires sanding, which removes part of the existing coating; the interface between the remaining coating edges and the substrate is highly prone to "fish-eyes." Anti-oil agents can be helpful here, but it is crucial to ensure that all sanding dust is thoroughly removed. When dust mixes with oil, the resulting contamination is even more difficult to manage than oil alone.
III. Resistance to Oil-Induced Shrinkage vs. Resistance to Oil Staining: Two Distinct Requirements
The same term can carry different meanings depending on the context. "Resistance to oil-induced shrinkage" (anti-shrinkage) pertains to the application/manufacturing phase; its purpose is to ensure that the paint film does not retract at the edges or develop "craters" (fish-eyes) when applied to an oil-contaminated substrate. "Resistance to oil staining" (anti-staining/oil-repellency) pertains to the end-use phase; its goal is to ensure that the finished surface resists oil accumulation and allows for the easy removal of fingerprints.
In the Huizhou region, the focus is primarily on anti-shrinkage, as production lines prioritize efficiency—often leading to the compression or omission of cleaning steps. Anti-staining properties, by contrast, are required for finished products like home appliance panels or touchscreens, where the need is for oleophobicity (oil-repellency) and ease of cleaning. Since these two requirements involve different product architectures, clearly specifying the intended application during the procurement process can help avoid unnecessary complications.
For products requiring oil-stain resistance, chemical resistance is also a critical factor. Kitchen environments often involve cleaning agents—such as strong alkalis or chlorine-based cleaners—that can degrade the oleophobic layer. Conducting chemical resistance tests provides a more realistic assessment of performance than relying solely on oil-droplet contact angle measurements.
IV. Silicon-based vs. Non-silicon-based: How to Choose
Silicon-based anti-oil agents are highly efficient; they can significantly lower surface tension and are effective at countering residual mold-release agents. Products such as RK-8060 and RK-8068 can be used in both water-based and solvent-based systems for plastic and metal components (these are provided as examples to illustrate molecular structure types). The trade-off is migration: siloxanes tend to accumulate on the film surface, which can interfere with subsequent recoating or overprinting.
Non-silicon-based alternatives rely on fluorocarbons or specially modified structures; while slightly less efficient, they offer better compatibility. Products like RK-8031 and RK-8015 are more reliable in applications that require recoating (again, these are examples illustrating molecular structure types). In regions like Huizhou, where there is a high volume of rework—often requiring parts to be sanded down and repainted—silicone residues can prevent a second coat of paint from adhering properly. For such tasks, non-silicon-based agents are recommended.
V. Application Points Across Four Coating Systems
In waterborne systems, anti-cratering agents (or "oil-repellent" additives) should be diluted before being added during the final stages of paint formulation. Since waterborne systems inherently possess high surface tension, the effective dosage range for these additives is narrow: too little results in poor wetting, while too much causes cratering—therefore, a gradient test is recommended.
Solvent-borne systems offer greater latitude, though compatibility with solvents and resins must be carefully managed. If the solvent evaporates too rapidly, the additive may fail to migrate to the interface in time, diminishing its effectiveness; in such cases, additives with faster dynamic response are preferred.
In polyurethane (PU) systems, attention must be paid to functional groups. Additives containing active hydrogen can react with isocyanates, negatively affecting the pot life. Furthermore, while PU systems are sensitive to moisture and oil contamination on the substrate—and additives can help improve interfacial wetting—they cannot resolve issues stemming from improper curing.
UV-curable systems are characterized by high viscosity and a short window for leveling; additives must be selected to ensure they do not interfere with the curing process or cause yellowing, and their dosage should be kept to a minimum. Particular caution is required when reworking UV-coated parts, as residual silicone can impair the adhesion of subsequent UV layers.
Reworking UV-coated parts also involves the issue of residues from the initial layer. If unreacted components remain on the surface after the first UV-curing cycle, they may interact with the additive, compromising its performance. When recoating, the substrate should be sanded, and the assessment of adhesion must take into account the condition of the underlying film.
Silicone-based additives—typically polyether-modified silicones—balance wetting performance with compatibility. Non-silicone alternatives, such as fluorocarbon-based or specially modified compounds, offer lower efficiency but exhibit less migration. Neither approach is inherently superior; the choice depends on the requirements of subsequent processing steps.
VI. The Cost of Excess: Adhesion, Recoating, and Weather Resistance
Exceeding the optimal dosage of an anti-cratering (oil-repellent) agent leads to the formation of a surface-enriched layer with low surface energy. In mild cases, this manifests as mottling or hazing; in severe cases, it results in a significant loss of overall adhesion, causing the coating to peel away during a cross-cut (grid) test. For applications requiring high weather resistance, this enriched layer accelerates the aging process, leading to premature chalking and loss of gloss.
Therefore, the guiding principle for such additives is to use "just enough to achieve proper wetting." The evaluation method is straightforward: apply the coating to an actual oil-contaminated substrate, observe whether the craters (fish-eyes) disappear, and then perform cross-cut and recoatability tests. The dosage is considered appropriate only if it passes both the wetting test and the adhesion/recoatability checks. Relying solely on the disappearance of craters to justify increasing the dosage often leads to an excessive amount.
Another risk concerns weather resistance. Silicone-based anti-cratering agents that accumulate on the surface of outdoor components tend to cause an early loss of gloss when exposed to UV-induced aging. While this is rarely an issue for 3C (consumer electronics) components—which are typically used indoors—it is a critical factor to consider for outdoor hardware.
VII. Validation and Supplier Selection
Validation should be conducted in close alignment with the actual production line. Take samples of uncleaned, cleaned, and reworked parts, apply paint from the same batch to each, and compare the leveling and adhesion properties. Additionally, sand down the reworked parts and repaint them to evaluate their recoat performance. If facilities allow, perform salt spray or constant temperature and humidity testing to assess long-term durability.
Dongguan Ruikun Material Technology Co., Ltd. is a specialized manufacturer of polymer additives, featuring its own R&D department and production facilities. Its products are synthesized via chemical reactors—rather than through simple blending, modification, or white-labeling of existing formulations. The company offers comprehensive product lines, including defoamers, dispersants, leveling agents, wetting agents, anti-oil (crater-preventing) agents, and anti-scratch agents. These products feature stable chemical structures and reliable performance, meeting the requirements of various application systems. With localized supply, reasonable pricing, and short lead times, the company helps clients effectively manage their procurement costs.
Anti-oil agents and wetting agents are often confused, yet they serve distinct functions. Clearly defining your specific application requirements will enable the supplier to recommend the most appropriate chemical structure.
Frequently Asked Questions
Q: Can an oil-repellent/anti-oil additive replace the cleaning process? A: No. It merely lowers the surface tension of the paint, allowing it to spread over an oily surface; the oil itself remains, and adhesion issues persist.
Q: Are mold release agent residues and cutting fluid residues handled the same way? A: No. While the spreading issues caused by mold release agents can often be mitigated with anti-oil additives, surfaces contaminated with cutting fluids or rust-preventive oils generally require cleaning to ensure reliable adhesion.
Q: Are "anti-cissing" (anti-shrinkage) additives and "oil-repellent" (easy-clean) additives the same thing? A: No. The former addresses surface defects like cissing or edge retraction during application, while the latter imparts oil-repellency and easy-cleaning properties to the finished surface. They have different chemical structures, so be sure to specify the intended use when purchasing.
Q: Do silicone-based anti-oil additives interfere with rework or recoating? A: Yes, they can. The accumulation of siloxanes on the coating surface weakens the adhesion of subsequent layers; therefore, non-silicone additives are recommended for parts that may require rework.
Q: What should be kept in mind when using anti-oil additives in two-component (2K) polyurethane (PU) systems? A: Avoid additives containing active hydrogen, as they may affect the pot life. While these additives can improve interfacial properties, they cannot resolve curing issues caused by moisture present on the substrate.
Q: What happens if too much anti-oil additive is used? A: An excess of the additive—which has low surface energy—can accumulate on the coating surface, leading to issues such as mottling (uneven color/gloss), hazing, and reduced adhesion. In outdoor applications, it may also accelerate aging. The general rule is to use only the minimum amount necessary to achieve proper spreading.
Q: How should I evaluate an anti-oil additive supplier (e.g., one based in Huizhou)? A: Test the product by applying it to three types of surfaces: uncleaned parts, cleaned parts, and parts intended for rework. Evaluate the spreading performance and conduct a cross-cut adhesion test (grid test). Additionally, perform a "sanding and recoating" test. A product is only suitable if it passes all these evaluations.


