Professional provision of Chemical Auxiliaries
Provide high-quality products and technical services
Phone:0086-19876879286
Whatsapp:+86 13712258351
Enquiry
{name}{name} DEL
Contact Us
  • Dongguan Ruikun Material Technology Co.,Ltd.
  • TEL:0086-19876879286
  • Mobile phone:0086-19876879286
  • Whatsapp:+86 13712258351
  • Email:info@bestrkchem.com
  • Add:Jianshe Road, Nancheng District, Dongguan City

What problems do defoamers address in coatings and inks? A guide to selection across six different systems.

2026-11-20

What problems do defoamers address in coatings and inks? A guide to selection across six different systems.

 

Foam in coatings and inks often remains hidden while in the container, only becoming apparent during film formation, curing, or the printing process. Defects such as pinholes, craters, fish-eyes, blisters, and blurred halftone dots—while appearing distinct—frequently stem from the same root cause: the formation and entrapment of air bubbles, which then either rupture at the wrong moment or fail to rupture at all. Defoamers are designed to manage this process; however, the criteria for selecting a defoamer vary significantly depending on the system. Relying on a single product for every application often leads to new issues—suppressing foam in one area only to trigger surface defects like craters or "fish-eyes" in another. The following discussion categorizes these issues by defect type and system. (Note: The product names mentioned are provided solely as examples to illustrate specific molecular structure types.)

 

I. It primarily addresses four categories of issues:

Pinholes and craters. Air is introduced into the system during processes like mixing, grinding, or pumping. If these air bubbles fail to escape while the coating is still a wet film, they leave behind tiny holes once the film has cured. Larger bubbles may burst at the surface, creating depressions or "craters." This is particularly common in high-build flooring systems and thick-film screen-printed layers. The solution here lies in using "bubble-breaking" (defoaming) agents to eliminate the bubbles before the film sets.

Fish eyes and shrinkage cavities. These are often not caused by a failure to eliminate bubbles, but rather by the defoamer itself. Issues arise due to poor compatibility, excessive dosage, or the migration of silicone-based components, which create localized areas of low surface tension. This causes the surrounding wet coating to pull away, resulting in shrinkage cavities (craters) upon curing. To address this, one should reduce the dosage or switch to a more compatible additive.

Internal blistering and intercoat blistering. Air bubbles trapped within the coating layer may not be visible initially, but they can expand when exposed to heat or moisture, leading to a loss of adhesion. This is a major concern for thick-film coatings, high-solids formulations, and multi-layer coating systems. The root cause is inadequate "bubble suppression" (preventing bubbles from forming or stabilizing) rather than a failure to break existing bubbles.

Leveling, gloss, and storage stability. Uneven bubble distribution can lead to inconsistent film thickness after drying, resulting in issues like blurred print patterns or mottled appearances. In high-gloss clear coats and varnishes, incompatible additives can cause a hazy or "foggy" effect. Furthermore, in pigmented aqueous inks, continuous gas generation during long-term storage can lead to container swelling (bloating) and phase separation.

 

II. How to Choose Among Six Systems

Water-based coatings. Water has high surface tension, and emulsions contain inherent emulsifiers that promote foam stability; the challenge lies in breaking the foam effectively without leaving surface defects. For matte primers and architectural latex paints—where cost-effectiveness is the priority—mineral oil-based defoamers are sufficient; they offer long-lasting foam suppression and good compatibility. RK-8403 (provided as an example of a specific molecular structure type) is recommended; it should be added during the grinding stage at a dosage of 0.1% to 0.5%. Note that this type is not suitable for high-gloss, transparent topcoats. For water-based high-gloss industrial coatings and water-based polyurethane (PU) clear coats, where appearance is critical, polyether-modified silicone-based defoamers—such as RK-8405—are recommended (dosage: 0.1% to 0.5%). In multi-layer coating systems or applications where a subsequent film/laminate will be applied, silicone migration poses a risk; in these cases, use a non-silicone polymeric defoamer, such as the water-compatible RK-3062 (dosage: 0.5% to 1.5%).

 

Solvent-based coatings. Solvents have low surface tension, allowing bubbles to break quickly; however, the difficulty arises when bubbles rise slowly or become trapped in thick-film applications. For epoxy flooring or high-viscosity pigmented coatings applied in thick layers, silicone-based defoamers are preferred—RK-3109 is recommended at a dosage of 0.05% to 0.5%. It is crucial to strictly control the dosage, as exceeding this range can lead to "fish-eyes." For PU wood clear coats, high-gloss baking enamels, and multi-layer coating systems, use non-silicone polymeric defoamers to avoid adhesion issues during recoating caused by silicone migration; RK-3120 is recommended (dosage: 0.3% to 1.0%), as it offers excellent compatibility with esters and ketones. For coil coatings and thin-film topcoats, use polyether-modified silicone defoamers at low dosage levels, determining the optimal amount through small-scale gradient testing.

 

Water-based inks. Flexographic and rotogravure water-based inks are subject to high-speed, dynamic foaming. Defoamers must suppress foam during the grinding stage without compromising dot definition or registration (color-to-color alignment) during printing. For water-based packaging inks and flexographic inks—which primarily utilize inorganic pigments—RK-8405 or RK-8409 are recommended at a dosage of 0.1% to 0.5%. The majority should be added during the pigment-grinding stage, with a small amount reserved for final ink adjustment. For high-gloss water-based overprint varnishes, food-contact packaging, or applications requiring subsequent lamination, a silicone-free additive like RK-3062 is ideal; it prevents silicone migration and ensures strong lamination adhesion (recommended dosage: 0.5% to 1.5%). For high-pigment carbon black inks, silicone-free additives are also preferred to minimize carbon black flocculation and conflicts with dispersants.

 

In solvent-based inks, thick-film screen printing is particularly prone to air entrapment; the slow evaporation of solvents means the ink sets before bubbles can escape. For thick-film screen printing and colored inks, a silicone-free polymer such as RK-3078 is recommended (dosage: 0.3% to 1.0%); it is compatible with nitrocellulose and chlorinated polypropylene (CPP) binders and does not interfere with the drying process. For high-solids solvent-based rotogravure inks, a silicone-based additive like RK-3108 is recommended—it offers rapid defoaming at low dosages—though it is suitable only for single-layer applications that will not be overprinted.

In UV-curable systems, curing occurs in seconds, meaning any bubbles present become permanently trapped within the film. The primary concern here is ensuring the defoamer does not interfere with the curing process. Standard silicone-based or water-based defoamers are unsuitable, as they can inhibit polymerization, cause pinholes, or result in a tacky surface. A silicone-free additive designed for UV systems, such as RK-3162, is recommended; its acrylic-based structure does not inhibit polymerization and is effective at removing micro-bubbles (dosage: 0.1% to 0.6%). For thick-film UV floor coatings or heavy-deposit screen-printed inks, a high-efficiency silicone-free defoamer should be added prior to grinding, allowing bubbles to rise to the surface before the coating cures.

 

Pigment pastes are semi-finished products intended for use across various downstream systems; therefore, broad compatibility and long-term foam suppression are more critical than instantaneous bubble-breaking performance. For general-purpose water-based color pastes, use RK-8400 or RK-8404 during the grinding/milling stage if the formulation is primarily based on inorganic pigments. For pastes containing carbon black or organic pigments—especially those intended for subsequent incorporation into UV or PU systems—use the silicone-free additive RK-3062 to minimize issues such as cratering (fish-eyes) and poor adhesion after the transfer process.

 

III. General Principles Applicable Across Various Systems

Add the defoamer in two stages: incorporate 60%–70% during the grinding phase (to suppress foam formation) and the remainder during the paint-mixing/let-down phase (to break existing foam). Adding the entire amount at the final stage can lead to localized over-concentration, resulting in oil spots or craters (fish-eyes). There is a critical dosage threshold—typically ranging from 0.1% to 0.5%—so it is best to determine the optimal level through a gradient test (starting low and increasing). Carbon black-based systems require special consideration; due to their high specific surface area and strong adsorption capacity, they can "consume" a portion of the defoamer components, often making it appear as though the additive is ineffective. For such formulations, prioritize non-silicone or modified polyether-based defoamers that exhibit weaker adsorption, and ensure they are compatible with the chosen dispersants. Water-based additives and solvent-based additives are not interchangeable; a mismatch in the carrier medium can lead to poor dispersion, whitening (hazing), or the appearance of numerous "fish-eyes." When conducting small-scale trials, always account for the actual operating conditions—the foam encountered in a laboratory beaker is not on the same scale as that found on a printing press or a roller-coating line.

 

FAQ

1. Silicone-based defoamers are highly efficient at breaking bubbles, so why are they often avoided in high-gloss or recoatable systems? Silicones have extremely low surface tension; while this makes them highly efficient, it also carries a high risk of migration. If used in excess or if they lack sufficient compatibility, they can cause issues such as craters (fish-eyes), haze, and poor intercoat adhesion. For multi-layer coating systems, film lamination, or food packaging applications, non-silicone defoamers are preferred.

 

2. Should a defoamer be added during the grinding stage or the paint-letdown (mixing) stage? It should be added at both stages. About 60%–70% of the total dosage should be added during the grinding stage to suppress micro-bubbles generated by the shear forces of the bead mill. The remainder should be added during the letdown stage to control foaming caused by mixing and pumping. For UV-curable and high-build coatings, it is best to add the defoamer early in the process to ensure bubbles are released before the coating cures.

 

3. Why might a defoamer work well with inorganic pigments but fail when carbon black is used? Carbon black has a large specific surface area and strong adsorption capacity; it can adsorb some of the active components of the defoamer, effectively reducing the amount available to perform its function—leading to a noticeable drop in performance. For formulations containing carbon black, it is best to use non-silicone or modified polyether-based defoamers that exhibit lower adsorption, and to verify their compatibility with the dispersants used.

 

4. Can water-based defoamers be used in UV-curable systems? This is not recommended. Most water-based defoamers contain water and emulsifiers, which can inhibit the polymerization of UV-curable systems, leading to pinholes or a tacky surface after curing—often becoming apparent only after the coating has reached a "surface-dry" state.

 

5. Is it better to add as much defoamer as possible? No. There is an optimal "effective window" for dosage. Exceeding a certain critical threshold disrupts compatibility, immediately triggering issues like craters, haze, and poor recoatability. It is best to conduct a gradient test (e.g., at 0.1%, 0.2%, and 0.3% concentrations) and select the lowest effective dosage.

 

6. Can water-based defoamers be used directly in solvent-borne systems? No. The carrier and emulsification system are incompatible with solvent-borne formulations. Adding them can lead to poor dispersion, precipitation, whitening, widespread cratering, and compromised adhesion.

 

7. Why might a water-based ink show no foam during small-scale laboratory testing, yet exhibit severe foaming when used on a production press? Static mixing and high-speed dynamic foaming are not the same thing. During press operation, the ink fountain, ink rollers, and circulation pump continuously introduce air into the system; furthermore, the rate at which dynamic surface tension is re-established also plays a role. When selecting products, evaluate their foam-suppression performance under actual dynamic operating conditions—ideally by conducting comparisons under the specific parameters of your printing process.