Professional provision of Chemical Auxiliaries
Provide high-quality products and technical services
Phone:0086-19876879286
Whatsapp:+86 13712258351
Enquiry
{name}{name} DEL
Contact Us
  • Dongguan Ruikun Material Technology Co.,Ltd.
  • TEL:0086-19876879286
  • Mobile phone:0086-19876879286
  • Whatsapp:+86 13712258351
  • Email:info@bestrkchem.com
  • Add:Jianshe Road, Nancheng District, Dongguan City

When facing issues with grinding efficiency or particle fineness in coatings, inks, or inkjet formulations, how should you re-evaluate your choice of dispersant?

2026-11-20

When facing issues with grinding efficiency or particle fineness in coatings, inks, or inkjet formulations, how should you re-evaluate your choice of dispersant?

 

Poor grinding efficiency is rarely due to a lack of power from the equipment itself; rather, it stems from a failure to effectively transmit that energy to the particles. Bead mills rely on the shear forces and collisions between grinding beads to perform work. For these beads to move, they must be carried along by the slurry—but if the slurry is too viscous, the beads become immobilized, and if it is too thin, they simply slide past one another. During the grinding stage, the dispersant’s primary role is to open up interfaces and adjust the viscosity to an optimal range, ensuring that mechanical energy is effectively applied to the pigment agglomerates. It is also responsible for deagglomeration and subsequent stabilization. Therefore, if you encounter problems like "ineffective grinding" or "inability to achieve sufficient fineness," do not rush to change your grinding beads or extend the processing time; instead, first examine the dispersion process. The product designations mentioned are merely examples used to illustrate specific types of molecular structures.

 

I. Grinding efficiency is determined by three stages:

Wetting. The resin, solvent, or water must first penetrate the interstices of pigment agglomerates to wet the particle surfaces; only then can subsequent mechanical shearing be effective. In systems where wetting is slow, the process may stall—even after an hour of grinding, the fineness remains unchanged.

Deagglomeration. Dispersants adsorb onto the particle surfaces, weakening the interparticle attractive forces and allowing shear forces to break apart the agglomerates. The efficiency of this stage is directly linked to the "anchoring strength" of the dispersant; if it cannot anchor effectively, even intense shear will only reduce large agglomerates into smaller ones, failing to reach the level of individual, discrete particles.

Viscosity and Energy Transfer. When dispersion is achieved, the system’s viscosity falls into an optimal range, allowing the grinding beads to flow smoothly and maximizing the efficiency of collisions and shear. This factor is most frequently overlooked: many people focus solely on fineness while ignoring viscosity—yet, in reality, viscosity acts as the "on/off switch" that determines whether the grinding beads can perform their work.

 

II. A Counterintuitive Point: Excessive Dispersion Can Hinder Particle Size Reduction

It is easy to understand why insufficient dispersant makes grinding ineffective—the material simply cannot be processed. However, adding too much dispersant can be equally counterproductive, as it causes the viscosity to drop too low. When the slurry becomes too thin, the grinding beads begin to slip, rotating along with the slurry rather than moving relative to one another. This eliminates the necessary shear force, causing energy to be wasted on the agitator shaft instead of the grinding process. In practice, this manifests as a failure to achieve the target fineness despite prolonged grinding, often accompanied by a rise in temperature.

Another issue is "over-grinding." While the target fineness may be surpassed, the material's performance actually deteriorates. For instance, if titanium dioxide is ground to a particle size significantly smaller than its optimal light-scattering diameter, its hiding power diminishes. Furthermore, prolonged exposure to high shear forces can break the molecular chains of the dispersant, ultimately compromising the stability of the dispersion. Therefore, grinding is not a case of "the longer, the better"; the process should be stopped precisely when the target fineness is reached.

 

III. Four Critical Checks Before a Product Changeover

Check if the dosage is calculated based on the pigment's specific surface area. A smaller particle size corresponds to a larger specific surface area, which requires a higher dosage of dispersant. Carbon black and organic pigments have specific surface areas several times greater than those of inorganic pigments; therefore, a dosage based simply on a fixed percentage of the total formulation is often insufficient.

Verify whether the dispersant is added at the correct stage. It must be introduced before the pigment is added or during the premixing phase so that it can occupy the pigment surface. Adding it after the milling process is complete may improve viscosity, but it cannot effectively deagglomerate the particles.

Ensure that the milling parameters are appropriate. The size of the zirconium beads, the bead-filling ratio, the tip speed, and the flow rate determine the achievable fineness. Larger beads are suitable for coarse milling, while smaller beads are required to reach the sub-micron range. For instance, achieving a D90 of under 200 nanometers is generally impossible when using 1 mm beads—a limitation that cannot be compensated for by simply adjusting the dispersant.

Consider temperature and batch conditions. Excessive temperature rise during milling can cause the dispersant to lose its effectiveness and lead to solvent evaporation, which alters the system. Using the same milling parameters in both summer and winter can result in significant differences in the final outcome.

 

IV. Selection Strategies Across Seven Application Areas

Water-based coatings. For titanium dioxide and heavy calcium carbonate in latex paints—materials that are easy to grind but prone to settling—use dispersants like RK-4008DH or RK-4010 (examples provided to illustrate molecular structure types). The key is to adjust the viscosity to an optimal range for the grinding media (beads) to function effectively, rather than simply increasing the dosage. For paints containing organic pigments that are difficult to disperse, switch to RK-4017G or RK-4039AB; these offer strong anchoring and high deagglomeration efficiency—just ensure the dosage is adjusted based on the specific surface area of the pigment.

 

Solvent-based coatings. In baking enamels, polyurethane (PU), and epoxy systems, grinding efficiency is heavily influenced by resin viscosity. Use RK-4021 or RK-4031—grades that contribute minimally to viscosity—to enhance bead-milling efficiency. Carbon black is the most challenging to grind; utilize a multi-point anchoring structure like RK-4035AC. The dosage must be sufficient relative to the carbon black’s surface area; otherwise, you may never reach the target fineness, no matter how long you grind.

 

UV systems. Characterized by a lack of solvents and high viscosity, these systems present the greatest challenges for grinding efficiency. Select dispersants that contribute little to viscosity and are compatible with the monomers; this helps bring the system into a grindable viscosity range. Additionally, strictly control the grinding temperature, as UV monomers can undergo complex interactions at high temperatures—prolonged grinding may actually lead to adverse issues.

 

Water-based inks. These systems feature high pigment concentrations but low overall viscosity; failure to achieve sufficient fineness results in poor dot definition (faint or blurred halftone dots). For general-purpose pigmented inks, use RK-4010 or RK-4017G; for carbon black, use RK-4059. First, ensure the dosage is adequate based on the specific surface area, then fine-tune the grinding media (zirconia beads) and flow rate.

 

Solvent-based inks. Screen-printing and rotogravure inks require even finer particle sizes than standard coatings, as thin ink layers cannot tolerate the presence of coarse particles. For general pigments, use RK-4020A or RK-4033; for carbon black, use RK-4035AC. If the desired fineness is not achieved, first review the dosage and the timing of the dispersant addition (i.e., whether it is added upfront), then consider using smaller grinding beads.

 

Inkjet applications. These have the most stringent requirements for fineness; the D90 value typically must be kept below 200 nanometers, as coarse particles will cause nozzle clogging. Select dispersants with a high molecular weight that offer low viscosity contribution and strong individual-particle dispersion capabilities. For water-based systems, consider RK-4039AB or RK-4059. For specialized sub-micron powder applications, products such as RK-4017EA or RK-4054EF are suitable choices. Inkjet milling usually involves a multi-stage process—coarse grinding, fine grinding, and filtration—requiring the dispersant to remain effective at every stage.

Color pastes (pigment concentrates). The milling efficiency of color pastes directly determines production capacity and costs. For general-purpose water-based color pastes, use RK-4010 or RK-4017G; for general-purpose organic pigment pastes, use RK-4059 or RK-4065A. Given the high solids content and high viscosity of these pastes, the dispersant’s ability to reduce viscosity often has a greater impact on output than its ability to deagglomerate particles.

 

V. How to Conduct Validation

Set up three comparative tests: the original formulation, a 20% increase in dosage, and a change in material grade. For each test, record four parameters: the time required to reach the target fineness, the particle size distribution at that point, the temperature and viscosity during the milling process, and whether the fineness "rebounds" (coarsens) after the material has sat for two hours. Relying solely on the fineness reading taken the instant milling stops is meaningless; the real issue is potential rebound. Additionally, plot the relationship between milling time and properties such as opacity and gloss to identify the "inflection point" where over-milling occurs—avoid the common pitfall of continuing to mill based purely on experience.

 

FAQ

1. If the fineness doesn't improve after prolonged milling, is it due to an insufficient amount of dispersant? Possibly—but it could also be an excess of dispersant or an inappropriate grinding bead size. First, check the viscosity during the milling process: if it’s too thick, dispersion is inadequate; if it’s too thin, there may be an excess of dispersant, or the system’s inherent viscosity is simply low. Next, verify whether the zirconium bead size is appropriate for the target fineness. Only after ruling out these factors should you consider switching to a different product model.

 

2. Why does adding too much dispersant prevent the material from reaching the desired fineness? If the slurry becomes too thin, the grinding beads will slip, preventing relative motion between them and failing to generate sufficient shear force. Energy is wasted on mere stirring rather than grinding, meaning the fineness remains unchanged while the temperature rises.

 

3. Why is carbon black so much harder to grind than titanium dioxide (TiO₂)? Carbon black has a large specific surface area and high oil absorption, which consumes a portion of the dispersant, leaving an insufficient amount to act effectively on the particles. Furthermore, because the particles are extremely fine and tightly agglomerated, they require stronger anchoring and smaller grinding beads. The dosage of dispersant must be recalculated specifically for the carbon black grade being used.

 

4. Why do I still encounter coarse particles even when the fineness gauge reading meets the target? A fineness gauge has limited resolution and cannot detect a small number of exceptionally coarse particles. For systems like inkjet inks or thin-film coatings, you should examine the "tail" of the particle size distribution (e.g., the D99 value) rather than relying solely on the median value.

 

5. What are the consequences of high milling temperatures? High temperatures can cause dispersants to degrade or lose effectiveness prematurely. Additionally, solvent evaporation alters the system's composition, which in turn affects viscosity. In summer, you must adjust both the cooling system and the flow rate; you cannot simply use the same parameters applied during the winter.

 

6. To achieve greater fineness, should I change the dispersant or the zirconium beads? First, determine whether the issue is that the material "won't grind further" (a dispersion or viscosity problem, requiring a change in dispersant type or dosage) or that it has "reached its limit" (a bead size problem, requiring smaller beads). Often, both issues occur simultaneously; they should be evaluated and verified separately.

 

7. Does longer milling time always result in better fineness? No. Once the target fineness is exceeded, pigments that rely on light scattering—such as titanium dioxide—may lose their hiding power. Furthermore, the molecular chains of the dispersant can be broken down, leading to reduced stability. Identify the inflection point in the "fineness vs. performance" relationship, and stop just before reaching it.